∺lt-D shortcut was made for the Clear Buffer command. The main filter and amplitude detector was fully rewritten.Ī set of main filter bandwidths was extended. This command is available in registered version of the software only. It saves receiving buffer in a temporary file and opens this file by a text editor.
The command File > Open Buffer in Notepad was made. Negative value means system default sound card. SoundCardNumber=0 means a first sound card, SoundCardNumber=1 means a second card etc. If there are several sound cards in a computer, you can select the card by the SoundCardNumber parameter of section of the CWGET.INI file. The bandwidth of a sound filter is selected by the Setup > Sound Output menu. If your sound card supports a full-duplex mode, you can use CwGet as narrow-band sound DSP-filter now. Preferred file parameters are mono, 16 bit, 11025 Hz.
WAVE-file must be Windows PCM file, without compression. See the File > Decode From File command. V1.30ĬwGet can decode signals from WAVE-file now. V1.36Ī problem with scrolling of received symbols window was fixed. When this option is enabled, data transferred to logger are copied to the Windows clipboard also. The Setup > Copy Transferred Data to Clipboard option was made.
In this mode software doesn't use popup-menu to catch word to logger.ĬwGet recognize callsign or control number automatically. The Setup > Catch Words in Contest Mode option was made. But you still can select the part of the text by Option is enabled, you can catch a word from RX window by single mouseĬlick, not double-click. The option Setup > Catch Word by One Mouse Click was made. V1.37ĬwGet removes all spaces in selected text transferred to a logger now. To move a visible part of spectrogram to left or right you need to drag it by mouse with Alt key pressed now. File is closed by the File > Close Wave Capture File command. The File > Open Wave Capture File command opens wave-file to save all received from soundcard sound. Special macrosequences can be used in the CwType software (V1.32 and later) to The The Save button writes previous 60 seconds of a sound to a wave The Replay button click makesĬwGet to replay previous 10 seconds of received signal. User-selectedįrequency is shown at spectrogram by short thin line.Ī one minute sound buffer was made.
Maximal deviation from last user-selected frequency. Second parameter is global deviation in hertzs, i.e. The first parameter is local deviation in hertzs, i.e. Oscillogram drawing was improved, especially under Windows 2000/XP. User can select soundcards used for sound input and output by Setup > Input Sound CardĪnd Setup > Output Sound Card menu now. Hamport software uses this interface also. Tuning is made via OmniRig software interface. In this case auto-tuningīy RIT is impossible. That not every transceiver has programmable RIT. Made by RIT or by VFO according selected option. Auto-tuning is madeĪfter click on spectrogram or by GoToMax command. Is changed to consist RX frequency to TX frequency. The Setup > Tune RIG by menu switches on the mode of automatic Is selected CwGet make fast AFC to near station after mouse click on spectrogram regardless of the ∺FC button state. The Setup > AFC at Mouse Click option was made. When the Setup > AFC at mouse click option is selectedĪ fast AFC is made by click at spectrogram, but it is not made by click at frequency ruler below now. V1.47Ī problem of frequency control of some RIG types was fixed. Menus can change colors of all elements of spectrogram or oscillogram window now. The Setup > Spectrogram Colors Setup and Setup > Oscillogram Colors Setup The Setup > Tune RIG by > Show Omni-Rig Setup command activates Omni-Rig setup dialog. Subscribe for our mailing list! Enter your e-mail A tool for monitoring popular web-cluster service from OH9W/OH2AQ Radio Club A comprehensive logger program designed for amateur radio station operatorsĬluster monitor.
CwGet - CW morse code decoder :: ProductsĪALog.